Modelling and investigating primary beam effects of reflector antenna arrays
- Authors: Iheanetu, Kelachukwu
- Date: 2020
- Subjects: Antennas, Reflector , Radio telescopes , Astronomical instruments -- Calibration , Holography , Polynomials , Very large array telescopes -- South Africa , Astronomy -- Data processing , Primary beam effects , Jacobi-Bessel pattern , Cassbeam software , MeerKAT telescope
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10962/147425 , vital:38635
- Description: Signals received by a radio telescope are always affected by propagation and instrumental effects. These effects need to be modelled and accounted for during the process of calibration. The primary beam (PB) of the antenna is one major instrumental effect that needs to be accounted for during calibration. Producing accurate models of the radio antenna PB is crucial, and many approaches (like electromagnetic and optical simulations) have been used to model it. The cos³ function, Jacobi-Bessel pattern, characteristic basis function patterns (CBFP) and Cassbeam software (which uses optical ray-tracing with antenna parameters) have also been used to model it. These models capture the basic PB effects. Real-life PB patterns differ from these models due to various subtle effects such as mechanical deformation and effects introduced into the PB due to standing waves that exist in reflector antennas. The actual patterns can be measured via a process called astro-holography (or holography), but this is subject to noise, radio frequency interference, and other measurement errors. In our approach, we use principal component analysis and Zernike polynomials to model the PBs of the Very Large Array (VLA) and the MeerKAT telescopes from their holography measured data. The models have reconstruction errors of less than 5% at a compression factor of approximately 98% for both arrays. We also present steps that can be used to generate accurate beam models for any telescope (independent of its design) based on holography measured data. Analysis of the VLA measured PBs revealed that the graph of the beam sizes (and centre offset positions) have a fast oscillating trend (superimposed on a slow trend) with frequency. This spectral behaviour we termed ripple or characteristic effects. Most existing PB models that are used in calibrating VLA data do not incorporate these direction dependent effects (DDEs). We investigate the impact of using PB models that ignore this DDE in continuum calibration and imaging via simulations. Our experiments show that, although these effects translate into less than 10% errors in source flux recovery, they do lead to 30% reduction in the dynamic range. To prepare data for Hi and radio halo (faint emissions) science analysis requires carrying out foreground subtraction of bright (continuum) sources. We investigate the impact of using beam models that ignore these ripple effects during continuum subtraction. These show that using PB models which completely ignore the ripple effects in continuum subtraction could translate to error of more to 30% in the recovered Hi spectral properties. This implies that science inferences drawn from the results for Hi studies could have errors of the same magnitude.
- Full Text:
- Date Issued: 2020
Advanced high speed data and clock transmission over optical fibre for square kilometre telescope array
- Authors: Isoe, George Mosoti
- Date: 2018
- Subjects: Very large array telescopes -- South Africa , Semiconductor lasers Optical communications Optical amplifiers
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10948/30375 , vital:30935
- Description: There is an ever present need from Internet users for more bandwidth. This is manifested by continuous increase in bandwidth demanding applications such as 5G wireless, new end user consumer links like thunderbolt, video conferencing, high definition video-on-demand transmitted over the Internet and massive data transfers required with and within data centres for backup, storage and data processing in cloud computing. Fibre optic communications technologies are playing a pivotal role in communication, being a major enabling technology in our increasingly Internet-centric society. As network services continue to become more dynamic and diverse, Internet service providers are faced with a challenge of cost reduction in the transmission network, power and spectral efficiency as well as scalability of the optical network infrastructure to support incremental expansions and virtual machines. Intelligent design of terrestrial optical networks to allow for simultaneous signal transmission through shared network infrastructure, and the use of low cost, power efficient, high bandwidth transmitters such as vertical surface emitting lasers (VCSELs) as well as exploitation of spectral efficient in-complex advanced modulation formats is a viable approach to this situation. In this study, techniques for spectral efficiency upgrade and simultaneous transmission of data signal, reference frequency (RF) clock signal and pulse-per-second (PPS) over shared infrastructure have experimentally been optimized in a laboratory environment for adoption in next-generation telescope array networks such as the Square Kilometre Array (SKA), time keeping systems such as banking systems, Coordinated Universal Time(UTC) timing and Global Positioning Systems (GPS), as well as high capacity spectral efficient short reach optical fibre networks such as data centres. This work starts by experimentally optimizing VCSEL technology for simultaneous transmission of 10 Gbps data and 1.712 GHz RF clock signal over a single G. 655 optical fibre of length 24.75 Km at different channel spacing and different propagation direction for implementation in a cost effective next-generation telescope array network. The wavelength tuneability property of VCSEL transmitters allows for wavelength adjustment, a key requirement for simultaneous data and RF clock signal transmission over a single optical fibre. A receiver sensitivity of -19.19 dBm was experimentally achieved at back-to-back analysis. A 24.75 Km of simultaneous data and RF clock signal transmission performed at 0.4 nm channel spacing introduced a transmission penalty of 1.07 dB and 1.63 dB for counter and co-propagation scheme respectively. This work mainly utilized direct modulation and direct detection using a positive intrinsic negative (PIN) due to its simplicity and cost effectiveness. A novel modulation technique for simultaneous data and polarization-based pulse-per-second timing clock signal transmission using a single VCSEL carrier is experimentally demonstrated. Two signal types, a directly modulated 10 Gbps data signal and a polarization-based pulse per second (PPS) clock signal are modulated onto a single mode 10 GHz bandwidth VCSEL carrier at 1310 nm. Spectral efficiency is maximized by exploiting the inherent orthogonal polarization switching of the xiv VCSEL with changing bias in transmission of the PPS signal. A 10 Gbps VCSEL transmission with PPS over 11 Km of G.652 fibre introduced a transmission penalty of 0.52 dB. The contribution of PPS clock signal to this penalty was found to be 0.08 dB. A technique for simultaneous directly modulated data and phase modulated reference clock signal transmission over a signal channel in wavelength division multiplexing (WDM) solutions is experimentally demonstrated. This is to prepare solutions to the ever-increasing demand over gigabit/s, terabit/s and gigahertz capacities in WDM-based terrestrial optical fibre transmission systems such as telescope array networks. a total capacity of 30 Gbps (310 Gbps) data and 12 GHz ( 4 3 GHz) reference clock signal are multiplexed at a channel spacing of 100 GHz and simultaneously transmitted over a single mode G.655 fibre of length 24.73 Km. The recovery of the phase modulated RF clock signal using a differential delay line interferometry technique is experimentally demonstrated. A 625 Gbps (2525 Gbps) DWDM data transmission system is further implemented in simulation by multiplexing 25 channels at 25 Gbps per channel using 50 GHz channel spacing. A four level pulse amplitude modulation (4-PAM) data modulation format employing VCSELs is experimentally demonstrated for adoption in high bitrate networks such as big data science projects and data centre networks. 4-PAM offers a good trade-off between complexity, efficiency, reach, and sensitivity. A software defined digital signal processing (DSP) receiver is designed and implemented in MATLAB to recover the transmitted 4-PAM data signal cost effectively without the necessity of costly receiver hardware. A novel technique for maximizing carrier spectral efficiency through simultaneous 20 Gbps 4-PAM data and phase modulated 2 GHz RF clock signal transmission on a single mode 10 GHz bandwidth VCSEL carrier at 1310 nm is experimentally demonstrated for the first time to the best of our knowledge. Data transmission and clock stability performance of the designed high spectral efficient VCSEL-based link network is evaluated through BER curve plots, phase noise measurements and Allan variance analysis respectively. VCSEL-based Raman amplification is experimentally demonstrated as a viable approach for RF clock signal distribution in extended reach astronomical telescope array networks and other extended reach terrestrial optical fibre network application. This is achieved by adopting two pumping techniques namely forward pumping and backward pumping. A maximum on off gain of 5.7 dB and 1.5 dB was experimentally attained for forward pumping and backward pumping at 24 dBm pump power respectively, while a maximum 100.8 Km fibre transmission achieved experimentally. In summary, this study has successfully demonstrated in-complex, spectral efficient, low cost and power efficient simultaneous data signal, reference frequency (RF) clock signal and pulse-per-second (PPS) transmission techniques over shared network infrastructure. Simultaneous transmission of data, RF clock and PPS timing signal is relevant in nextgeneration telescope array networks such as the Square Kilometre Array (SKA), time keeping systems such as banking systems, Coordinated Universal Time (UTC) timing and Global Positioning Systems (GPS), as well as high capacity spectral efficient short reach optical fibre networks such as data centres.
- Full Text:
- Date Issued: 2018